HOFTRONIC™ - Selby - LED Wall light with movement sensor - Incl. light sensor - IP65 waterproof - 780 lumens - 3000K warm white light - 10 watts - Black - Outdoor lamp - 5-year warranty

Tiltable wall light with movement sensor & light sensor

The Selby LED wall light with motion sensor is a tiltable, functional wall light with a brightness of no less than 780 lumens that you can mount in different places. The versatility of this LED wall lamp lies in its ability to tilt 240° vertically and 80° horizontally, allowing you to illuminate specific areas as desired. You can angle the lamp forward to cast light downward, or tilt it upward to direct the light forward. Additionally, the lamp can be adjusted sideways for further directional control.

With its built-in motion and twilight sensor, the Selby will automatically switch on when it gets dark or when the sensor detects movement. The twilight switch-on level and duration can be set as desired. This makes the lamp ideal for security lighting, especially in places where extra security is needed around a home or business. The sensor outdoor light provides enough light to properly illuminate an area such as your driveway or carport. Thanks to LED technology, it only uses 10 watts, which is good for the environment and good for your wallet! The LED wall light with sensor emits a warm white light of 3000K. Its IP65 protection rating makes it resistant to dust and splashing water allowing it to be left outdoors throughout the year.

Product benefits

• Beautiful design: The Selby wall lamp's stylish, modern design makes it a real eye-catcher at the front door as well as in other places.
• Tiltable: Adjust the lamp to your preference; it can be tilted both vertically and horizontally.
• High light output: This sensor wall light emits no less than 780 lumens. This is more than enough to brighten areas such as a driveway or garage.
• Adjustable light sensor: The Selby wall light automatically switches on at dusk. You can set the twilight or light level at which the light switches on.
• Motion sensor: The Selby wall lamp has a motion sensor with a detection range of up to 9 metres within a 140-degree angle. For instance, the lamp could automatically turn on the moment your car enters the driveway.
• Adjustable duration: Avoid wasting energy and decide how long the light stays on after motion is no longer detected. You can set it from 10 seconds to 15 minutes.
• IP65 waterproof: The wall light has an IP65 rating, making it suitable for outdoor use, even in rain or snow.
• 3000K warm white light: The Selby LED wall light produces an atmospheric warm white light. This makes it ideal for hanging by the front door, garage or shed, giving you enough light without being too bright.
• Easy to install: The Selby wall lamp is easy to mount with the included plugs and screws.
• Very well made: By using the highest quality materials, we guarantee a product that will give you years of enjoyment.
• Environmentally friendly & cost-effective: This lamp's LED technology and integrated sensors make it highly energy-efficient. It benefits not only the environment but also your wallet!
• 5-year warranty: At INTOLED, we deliver only the best quality, which is why this lamp comes with a 5-year warranty. Should anything break during these 5 years, we will replace it for free.

LED wall light with adjustable motion detector & light sensor

The Selby LED sensor wall light has both a motion sensor and a twilight switch. This means that the light reacts when it gets dark in the evening, but also switches on when it detects movement (up to a maximum of 9 metres).

The light sensor and the time duration are both adjustable via the buttons that are set under the cover of the sensor. Slide the cover down to access the buttons. The light sensor allows you to set the number of lux. If you set the lux level very low, the sensor will switch on the light when it is very dark outside (3 lux). Do you turn the knob all the way towards the sun? Then the sensor will switch on the lamp when it is still quite bright (> 300 lux) and the lamp will switch on at the slightest twilight. Finally, you can set how long the lamp stays on after it detects no movement. This saves money and energy by not leaving the floodlight on unnecessarily.

Stylish LED sensor wall light for indoor & outdoor use

The Selby LED wall lamp with a motion sensor is highly versatile, suitable for mounting in various locations, both outside and inside. The white light diffusing plate ensures that the light is evenly distributed, offering adequate illumination without being overly bright. This feature is particularly beneficial in areas like the front door, garage, driveway, and carport. Moreover, the downward direction of the lamp's light allows for precise illumination of specific areas, ensuring that the light does not intrude on the surroundings and enhances the overall aesthetic. This design also renders the lamp ideal for lighting up pathways, staircases, and entryways.

Its IP65 protection rating makes it resistant to dust and splashing water, so it can remain outdoors throughout the year, undeterred by rain or snow. This makes it the perfect sensor lamp for placement near the front door, driveway, or beside the garage door. Additionally, it serves well as a wall lamp along pathways by a shed, on garden fences, and in numerous other settings.

Applications:

• Driveway
• Front door
• Side facades
• Fences
• Garages
• Garden sheds
• Carports
• Backyard
• Front garden
• Entrance doors
• Cellars
• Stairwell
• Scullery 

Easy installation

The Selby LED wall light with sensor is easy to install:

1. Turn off the power.

2. Unscrew the back cover and thread the cables through the opening on the back of the lamp.
   
   Note. You can also connect the cables at the bottom of the lamp. There is a designated area for this, which you need to drill through from the inside first. 

3. Connect the cables following the connection diagram provided in the manual.

4. To attach the backplate to a wall, you first need to drill 2 holes in it at the designated spots.

5. Mount the back cover onto the wall using the supplied screws and wall plugs. Ensure the height is between 1.8 and 2.5 metres.

6. Reattach the lamp to the back cover.

7. Turn the power on. Please note: the sensor needs about 30 seconds to warm up. Once warmed up, it will begin to operate.